Frames

Frame Options

Depending on the product selected there are different frame options available. Each frame can be used individually, or they can be bayed together – joining hardware is included with each frame. The load capacity of each frame is determined by the manufacturing process and the shape of the mounting rail. All frames come with two pair of Thru-Hole mounting rails. The rails can be swapped our for tapped versions if desired. Scroll to see which frame styles are available with which product.


10 Series®

10 Series® frames are fully welded and can handle 3,500 lbs. of equipment evenly distributed and are available in 19″ and 24″ rack mount widths..
 

Vertical Frames
Vertical frames are available in 15U, 19U, 20U, 23U, 28U, 30U, 35U, 36U, 40U, 42U, 45U, and 48U heights. Depending on the height there are a different number of struts.

3 Strut

2 Strut


Vertical Frames with Work Surface Mounting Provisions
This style frame comes with provisions for mounting a work surface, out front, flush with the top of the frame. It is available in 14U and 18U heights.  

2 Strut

wt_2strut.gif


Slope Front Frames
Slope front style frames have a sloped portion in the front. The slope area has welded in Thru-Hole mounting rails to accommodate panels and rack mount equipment that does not require a rear attach point. This frame style is available with 10U, or 12U tall slope openings, while the lower section has 15U of space.

12U Slope Opening

10U Slope Opening

Slope Front Frames with Work Surface Provisions
Slope front style frames have a sloped portion in the front with provisions for mounting a work surface out front. The slope area has welded in Thru-Hole mounting rails to accommodate panels and rack mount equipment that does not require a rear attach point. This frame style is available with 10U, or 12U tall slope openings, while the lower section has 14U of space.

12U Slope Opening

10U Slope Opening


Wedge Frames

Wedge frames allow vertical and slope front frame styles to wrap around a corner. Wedge frames can be use next to any (19″ or 24″) EIA with frame, but be sure to make sure the depths match. Wedges must be installed on site. All joining hardware is included.

Vertical style wedge frames referred to as Flat Pack Wedge Kits, due to the way they ship, are be bolted to the side of other vertical style frames to form the desired console configuration.

Slope front wedge frames are fully welded and utilize solid non-removable front, top and rear panels with an open bottom and bolt on pontoon base.

Vertical

Slope Front


Turret
These frames assist in providing proper viewing angles for operators of electronic equipment. Each turret is supplied with welded in Thru-Hole mounting rails. Mounting hardware is included if not configured prior to shipment.

45° Turret

90° Turret


ESQ®

ESQ® frames are fully welded and can handle 800 lbs. of equipment evenly distributed. The frames come with a riser base (pontoon base) and is available in 19″ 24″ and 30″ EIA rack mount widths.

Vertical Frames
Vertical frames are available in 12U, 16U, 20U, 23U, 25U, 30U, 35U, 40U, and 45U heights. Depending on the height there are a different number of struts. 

4 Strut

3 Strut

2 Strut


Vertical Frames with Work Surface Mounting Provisions
This style frame comes with provisions for mounting a work surface, out front, flush with the top of the frame. It is available in 12U and 16U heights. Depending on the height there are a different number of struts.   

3 Strut

2 Strut


Slope Front Frames
Slope front style frames have a sloped portion in the front. The slope area has welded in Thru-Hole mounting rails to accommodate panels and rack mount equipment that does not require a rear attach point. This frame style is available with 6U, 10U, or 14U tall slope openings, while the lower sections have 14U or 16U of space.

14U Slope Opening

10U Slope Opening

6U Slope Opening


Wedge Frames

Wedge frames allow vertical and slope front frame styles to wrap around a corner. Wedge frames can be use next to any (19″, 24″, or 30″) EIA with frame, but be sure to make sure the depths match. Wedges must be installed on site. All joining hardware is included.

Vertical style wedge frames referred to as Flat Pack Wedge Kits, due to the way they ship, are be bolted to the side of other vertical style frames to form the desired console configuration.

Slope front wedge frames are fully welded and utilize solid non-removable front, top and rear panels with an open bottom and bolt on pontoon base.

Vertical Wedge

Slope Front Wedge


Turret, Instrument, Riser Frames
These frames assist in providing proper viewing angles for operators of electronic equipment. Each turret is supplied with welded in Thru-Hole mounting rails. Mounting hardware is included if not configured prior to shipment.

20° Turret

25° Turret

35° Turret

19° Turret

35° / 55° Turret

55° / 35° Turret

Riser

Instrument


FP1

The following components make up the structure of an FP1 Console. Use them in combination to create the layout that works best for your space. Work from left to right when laying out the base structure.

Base and Turret

19” Base

24” Base

19″ Turret

24″ Turret


Wedges

30° Wedge

45° Wedge

90° Wedge

30° Reverse Wedge

90° Reverse Wedge

45° Reverse Wedge


FP2

The following components make up the structure of an FP2 Console. Use them in combination to create the layout that works best for your space. Work from left to right when laying out the base structure.

Legs

Left Leg

Right Leg

Gang Leg


Bays

1 Bay

2 Bay

3 Bay


Frames

19″ Frame

24″ Frame


Wedges

15° Wedge

22.5° Wedge

30° Wedge

45° Wedge

90° Wedge

15° Reverse Wedge

22.5° Reverse Wedge

30° Reverse Wedge

45° Reverse Wedge

90° Reverse Wedge